Wednesday, 9 October 2013

Fire Truck. Gas pedal clean up.

Small update from my last few evenings work...

The gas pedal on the cab looked in a pretty bad state, plenty of wet shoes and cold storage had caused the surface of the pedal to to turn a lovely glowing rust colour. I wasn't sure if I would need to spray this black to 'hide' any damage but as things got this has turned out nice :)
The metal backing plate was also sanded back, primed and sprayed in black, I with I had shares in black spray paint as I have used lots of it in the past year or so.

Pedal ass'y as found on the cab
Eek! elbow grease required, anyone got some!
A good bit of cleaning and polishing later...

Gripped up, with metal plate sprayed. Mmmm.
That's all folks! Only a quick update as time permits, the next update will hopefully be of the cab cosmetics complete, minus the monitor which will require a lengthy post as I've got some work to do retrofitting an LCD monitor ;o) a CRT monitor to replace the missing 23" Black and White which would have originally been installed.

Thanks, Mart.

Thursday, 3 October 2013

Fire Truck. Main cab, Work begins...

Moving on from the rear seat, its time to get the main cab on the road so it can put out some fires! Work carried out so far in no particular order.

  1. Cab stripped out of all components and thoroughly cleaned.
  2. New Leg levellers fitted and the cab had none, no doubt this had caused some of the damage around the bottom of the cab.
  3. Laminate sides glued back on.
  4. Small repair to a bottom section of the cab that broken off.
  5. New T-Moulding fitted.
  6. Top and rear section of cab re-fitted back into place with glue and original nails.
  7. New power switch fitted as the last one had been home to some wasps and I think they ate most of it!
  8. Wire loom had a bath and some new connectors fitted as the plastic had become brittle and snapped off the locking lugs.
  9. Power brick stripped and cleaned. All five fuse holders replaced as the old ones had gone brittle, both the internal metal and the plastic cases broke off when opening the holder to check the fuses.
  10. Steering assembly stripped and cleaned
Time for some photos...
Empty cab full of grime.
All the innards.
    I thought about taking the whole cab to bits but decided against it!
    After a clean up with paint on the transformer and new fuse holders
    Damage to the laminate side. New screws adding strength to the base.
    More T-Cut applied to clean the sides.
    Steering assembly stripped for maintenance.
    There's plenty more to do but things are moving on nicely, more soon.

                                 

    .



                                   





Thursday, 5 September 2013

Fire Truck. Rear seat Complete.

I have a couple more items that I've completed in this update. The rear seat now has new T-Moulding, and I've refurbished the coin door metal work along with the bracket that links the front and rear unit together. First up are the brackets that link the two halves of the cab together.

Before. Tardy, rusty paintwork.
With the help of my small hand sander, I got things looking like this.
Primed up in a matt finish.
Completed Item ready to fit back onto the seat.
I have also give the coin box a covering in the direct to rust primer, and I think I'm going to leave that in the matt black finish as it looks pretty good.

Coin box painted
Because the laminate sides has lost their stick to the main wood sides of the cab, I decided I would put the cabinet on its side, remove the T-Moulding, glue the sides back on and then refit the new T-Moulding.

There's no really much to show, but I used some spray contact adhesive on the wood of the cab and the laminate sides then after a few minutes the parts were pressed together. Once the glue had cured I then moved onto the T-Moulding. Starting with the underside of the cab to avoid any joins showing it was a case of using a mallet to guide the T-Mould into the existing slot, I did cut some of the groove out on the tight corners to make sure it pushed home and was a nice tight fit. The same process was repeated for the other side.

I've also stripped and resprayed the coin door, this looks really nice now and I'm happy with the results.



Below are a few photos of how the seat looks now. At this point there's not really a lot more that I'm going to do to the seat other than fitting a lock to the coin door and a bulb holder for coin door light. The next update will be when I make a start on the main cab.





Since the last update I have also resprayed the bolts that hold the 'Horn' button in place as well as the rounded head bolts that go through the control panel, even though the Control Panel isn't in great condition these items looked out of place in their original condition.

Finally, Andy from Andys-Arcade is in the process of looking at the game board. Hopefully it won't be a too painful repair for him, I'm really looking forward to making progress with the main cab now.

Thursday, 15 August 2013

Pole Position. Prepare to Qualify...

Well I've jumped the gun a bit and got myself a PP board from Mark at RetroClinic.com I say jumping the gun only because the other parts on the cab are are not finished but anyway. Everything fired up OK with the exception of the Audio, it is coming through both speakers but it sounds heavily attenuated so I have some work to do to hunt down what wrong on the audio amp side of things. My monitor still requires further adjustment to get some more width out of the game image but as a 1 hour test session tonight I'm happy :)


Sunday, 11 August 2013

Pole Position. Small update.

Small update to my Pole Position cab. I finally had a bit of spare time to sort the coin box and the service panel out. A quick respray and a clean of the wiring loom and counters.

Finished Coin box photo 1

Finished Coin box photo 2
My list of remaining things to do on the cab now are as follows in no particular order off the top of my head:
1. Re-spray the coin door and re-assemble coin mech wiring etc.
2. Fit new steering wheel sticker to replace manky old one. I already have a replacement.
3. Renew/tidy the black formica front of the cab, as its pretty messed up. I think its been spray painted in the past and touched up all over the place.
4. Make a cardboard bezel for the monitor.
5. Make a replacement back door.
6. Fit some locks.
7. Locate a gameboard i can call my own :)

Thanks, Mart.



Tuesday, 23 July 2013

Subelectro cab. Nearly complete.

So the cabs been up and running now for a good few weeks now, in its current configuration it running a dual Jamma adapter with Wonderboy & Pac-Land, I had to make a new frame for the monitor to turn it into the horizontal position, but all is now good with this cab. Photo below:


I'll have one more update on this cab when I get some marquee artwork and a gameboard back from repair.

Mart. ;)

Tuesday, 28 May 2013

Subelectro cab. No more rot.

With a long weekend ahead and good weather forecast, I decided to try and get the Subelectro cab back on its feet and get rid of all the remaining rotten chipboard. I was pretty much a case of using a jigsaw to cut away the damage then reconstructing the cab using new wood. I also primed and painted the new section of cab, sanded and sprayed the marquee holder and metal control panel, coupled with starting to put components back into the cab. Photos below. Enjoy :)

Completely rebuilt base of cab
Primed and ready for top coat
I decided on dark brown as the colour instead of the usual black

Mains transformer and monitor being reinstalled

Marquee section complete, cpo sitting loose. I also fitted some new rubber matting at the base of the cab which was originally there.

I'm pretty damn happy with the results so far. The G07 monitor fired up which was a bonus to say the least. I couldn't get my test board to sync up correctly but I'm sure that was more to do with me rushing to test it with loose wiring than it being an actual fault. I also made an adapter to Jamma for the Hunchback board that was in the cab which I fired up on my test rig.

Hopefully in my next post, the cab will be pretty much complete, with controls reassembled, and with any luck I'll have decided which game/s will run in the cab.

Regards, Mart.