Monday, 25 February 2013

Fire!!!













From an ebay auction a few years back...


Saturday, 2 February 2013

Pole Position Update: More cleaning and new edge connectors

I spent some time today doing a few more bits to the Pole Position cab. I got rid of the old edge connectors which had corroded pins and plastic casings that were warped and cracked. I cut the old connectors a few pins at a time and soldered them onto the new connectors, I've also used heat shrink to tidy and strengthen the connections.

New soldered edge connectors

Below is a photo of the cab with the front all cleaned up. Everything has been removed from the cab, cleaned and reassembled. The CPO has cleaned up very well, there is just one small area which has started to crack along the curve of the front, and a small area which has some marker pen on that I haven't been able to remove yet.

The steering wheel and gear mechanism have been totally stripped and re-greased. I'm finally getting excited about this cab now, I'm finally getting to the stage it's nearly ready to play.
Front view, CPO cleaned and Marquee light on


Next up is the pedal mechanism, which is working. The 5K Ohm pot measure out fine with a multimeter, as with the rest of the cab, its full of dirt, I will be stripping this down and giving is a new coat of paint along with some new grip tape for the pedal.

Here's a couple of photos of what it looks like now, the next update should be once I've completed the pedal assembly.
Foot pedal showing sign of rust

Foot pedal and its worn grip tape


Monday, 28 January 2013

Pole Position Before and After...Work In Progress


I got the cab from Phil's arcade clearance thread over on the UKVAC forums, It came in a pretty bad state, ( As I had already seen from the photos) missing Gameboard, Dead monitor and FFFFilthy to say the least.

I have currently misplaced a whole SD card full of photos, so there's not really a lot of in progress shots of the cab being stripped and cleaned, when I find it I will update the article.

Here's the photo's from the original post, as you can see the cab it pretty dirty, Its had a switcher installed at some point along with some good butchery on the loom, The rear wooden panel that holds 2nd ARII in place was broken. No Game board Present, but I could see the potential :)

Front view missing monitor at the time

Broken cabinet, Switcher, bird Crap and an old sandwich

Only real  damage to the cab is the bottom left corner as shown in photo

Power brick covered in 25 years of Arcade dust.
What I've done; well both ARII's have been rebuilt with new Caps and regulators, both had blown R29/30 usually due to poor edge connector connections, the power brick had the works too, with  a complete strip down and rebuild. Fuse holder, fuses, big blue and a coat of paint to tidy thing up. See photo below of the finished brick.


Here's some photos of the cab with all of the loom been cleaned and refitted. As you can see, the back panel still needed to be replaced at the time of these photos. But It now look a damn site better.



I'll be the first to admit that I'm no carpenter, but my attempt at remaking the wooden back panel didn't come out too bad. I made it from some old Ply wood that I had and coated in in black emulsion paint. I should have black vinyl, I might do this once other parts of the cab a completed.


Everything fixed in place

So next up for the cab is to sort the edge connectors out as they're both badly worn out. Here's what I currently have...


Worn out with the Power and Ground having been chopped off

Hopefully I'll have more updates in the next few weeks.

Cheers, Mart.

Wednesday, 16 January 2013

Atari Power Brick rebuilds


Part of the process of improving the reliability of my Atari cabs was to do rebuilds on the power bricks. The Pole Position brick was filthy and had been badly repaired, bypassing the original burnt out fuse holder. The final photo shows an after shot of all the rebuilt power bricks. Much better! and hopefully I've added to the future reliability of the cabs.


Atari Asteroids Power Brick
Asteroids before.
Atari Batttle Zone Power Brick
Battle Zone before.

Atari Centipede Power Brick
Centipede before.

Atari Missile Command Power Brick
Missile Command before.


Atari Pole Position Power Brick
Pole Position before. This Power Brick was filthy!
The end result, after being stripped down, cleaned, painted, having new fuse holders and crimps.


 Regards, Mart.

Saturday, 12 January 2013

My Arcade Shed, Outhouse and Garage

I've added three new pages under the projects section on the right hand side ----> which show a small selection of photos from my past and present home arcades. A couple of the photos are below.

1997-2006 Arcade
2007-2010 Outrun in the Arcade

2011-Present Arcade



Tuesday, 8 January 2013

Welcome to Jumpnfire.com

Post #1 08/01/2013 20:15 

New blog on line with hopefully continuing updates about my arcade collecting and all my other geeky projects!

Still have loads to do to get the site as I want it. Graphics/Colour scheme layout etc.

Regards, Mart.

Photo of me. Martin Lawes